Serving Central New Jersey

New roof in Wall, NJ

What Is Underneath Your Shingles, and Why It Decides How Long the Roof Lasts

Almost every roofing conversation is about shingles. Which brand, which color, how many years. That is understandable, because shingles are the part you can see from the street, but it puts the emphasis in an odd place. The shingles are the wear layer. Most of what keeps water out of your house sits underneath them, and most of what goes wrong on a roof goes wrong down there.

Here is what is actually in the assembly, working from the framing up.

The deck

The deck is the structural surface the roof is built on, usually plywood or oriented strand board nailed across the rafters. On older houses around here it can be individual wood planks with gaps between them, which is fine until you try to fasten modern shingles into it.

The deck is the part nobody can assess until the old roof is off, which is why every honest estimate has a line about it. Two things go wrong: the sheets get soft from long-term moisture, usually near the eaves, in valleys, or around a chimney that has been leaking quietly for years; or the deck was thin to begin with and no longer holds a nail properly.

Ask how replacement decking is priced before work starts, and ask for the damaged sheets to be photographed as they come off. This is the most common place for an estimate to move, and the difference between a contractor who tells you the number in advance and one who discovers it on day two is largely a difference in how the conversation goes.

The ice barrier

This is a self-adhering rubberized membrane that sticks directly to the deck and seals around nails driven through it. It goes at the eaves, in the valleys, and around penetrations such as chimneys and skylights.

It solves two New Jersey problems at once. Inland, it is the defense against ice damming: when snow melts on a warm roof, runs to the cold overhang and refreezes, the resulting ridge of ice backs water up the slope under the shingles. Shingles shed water, they do not hold it back, so without a membrane that water finds the nail holes. Toward the shore, the same membrane is what stops wind-driven rain being pushed uphill under the shingle course in a nor easter.

The residential code that New Jersey works from requires an ice barrier along the eaves in regions where ice damming occurs, and it specifies how far up: far enough that the membrane extends to a point inside the exterior wall line, not merely to the edge of the overhang. On a low-pitch roof or a deep overhang, that means more than one course. It is worth confirming on your estimate how many courses are going down and where else the membrane is being used, because valleys and skylight perimeters are where roofs leak most often.

Underlayment

Underlayment covers the rest of the deck above the ice barrier. It is a secondary water barrier, protection for the deck between tear-off and dry-in, and a slip surface for the crew.

The traditional material is asphalt-saturated felt. The current standard is synthetic underlayment, a woven polymer sheet. Synthetic is lighter, far stronger, will not tear when the wind catches it, does not wrinkle when it gets wet, and gives a crew better footing on a steep slope. The difference shows up on the day the weather turns halfway through a tear-off, which in October is a realistic scenario. Felt still appears on some estimates because it is cheaper. It is not wrong, but it is worth knowing which one you are being quoted.

Drip edge

Drip edge is a bent metal flange fitted along the eaves and rakes. It costs very little and it does something specific: it carries water off the edge of the deck and into the gutter instead of letting it curl back underneath.

Without it, water wicks around the edge of the shingle and runs down the fascia board. Soft fascia, a gutter pulling away from the house, and rotten sheathing at the roof edge are all commonly the end of that chain. Code now requires drip edge on new roofs. If you are looking at an estimate that does not mention it, ask.

Starter strip

The bottom course of a roof needs a continuous strip of adhesive along the edge to hold the first row of shingles down against uplift. Manufacturers make a purpose-built starter for this, with the sealant in the right place.

The old shortcut is to cut up regular shingles and turn them upside down. It looks the same from the ground. What it does not do is put adhesive along the leading edge, which means the most wind-exposed course on the roof is the one relying on nails alone. It is also the detail most likely to invalidate a wind warranty. Same story at the rakes, where a proper starter matters on any house that catches weather off open ground or water.

Flashing

Flashing is metal formed to bridge the places where the roof meets something else: a wall, a chimney, a skylight, a vent pipe. It is where most leaks begin, and it is where corners get cut, because doing it properly takes time and replacing it costs more than sealing it.

The detail worth asking about is step flashing at any roof-to-wall intersection. Step flashing means individual pieces woven into each shingle course, each one overlapping the one below. The shortcut is a single long piece of bent metal, or worse, a bead of roof cement. Roof cement is not a flashing material. It is a temporary measure that hardens, shrinks and cracks, generally within a few seasons.

The other question is whether existing flashing is being reused. Sometimes that is reasonable, on a chimney with sound counterflashing set into the mortar. Often it is not, and reusing twenty-year-old flashing under a new roof is how a new roof leaks in year two. Our post on why roofs leak around chimneys and skylights goes further into that.

Ventilation ties it together

None of the above works well on a roof that cannot breathe. Trapped heat and moisture in the attic cook shingles from the underside, shorten their life, and in winter they are what makes a roof deck warm enough to start an ice dam in the first place. Intake at the soffits and exhaust at the ridge is the usual arrangement, and it has to be balanced to do anything. We covered the symptoms in signs your attic is not ventilated properly.

What this means when you read an estimate

You do not need to become a roofer. You do need enough vocabulary to tell a specific scope from a vague one. An estimate that lists the ice barrier and where it goes, names the underlayment, includes drip edge and manufactured starter, says what happens to the flashing, and gives a price for replacement decking is describing a roof. An estimate that says tear off and install new shingles with a price at the bottom is describing a number.

Those hidden layers are also a fair part of why two quotes for the same house can differ substantially, which we get into in what determines the cost of a new roof. If you want the assembly walked through on your own roof, that is what a roof installation conversation should cover before anyone quotes a color.

Related Posts